Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 14 Next »

Perkin Elmer Ultraview Vox Confocal

Location: Room 1.12, MRC Building

A Yokogawa CSU-X1 spinning disc system designed for rapid acquisition of 3D (XYZ) and 4D (XYZT) confocal data. The system is built around a Nikon TiE inverted microscope and uses a Hamamatsu C9100-13 EMCCD camera (512 x 512 pixels) to acquire low light level images. A Prior NanoscanZ piezo focus device allows fast collection of image stacks. The TiE microscope is fitted with the Perfect Focus System (PFS), which maintains samples in precise focus indefinitely (most suitable for samples mounted at a glass/aqueous interface, but there are some exceptions). The Vox system also has a Photokinesis Unit (PKU) for spot or ROI illumination in techniques such as FRAP and photoactivation/photoswitching.

  • Objective lenses
  • Microscope filter sets
  • Lasers
  • Emission filters

Objective Lenses

Magnification

Immersion Medium

Designation

Numerical Aperture

Coverslip Correction

Working Distance(mm)

10X

Air

Plan Apo

0.45

0.17

4

20X

Air

Plan Apo VC

0.75

0.17

1

40X

Air

Plan Apo

0.95

0.17

0.14

63X

Oil

Plan Apo

1.4

0.17

0.13

100X

Oil

VC Plan Apo

1.4

0.17

0.13

63X

Water

Plan Apo

1.2

0.17

0.27

  • There is also a 100x 1.3 NA Plan Fluor oil objective that can be used if the PFS range turns out to be too narrow when using the 100x Plan Apo
  • The 60x water lens is useful when imaging beyond about 10 μm in aqueous media. Matching the RI of the immersion media to water helps reduce spherical aberration when imaging far beyond the cover-slip surface
  • There is a choice of three immersion oils:

Oil

Refractive Index

For use with...

Kept in...

Cargille Type HF

1.518 (at 23ºC)

Oil lenses at room temperature

Tray outside environmental chamber

Cargille Type 37

1.518 (at 37°C)

Oil lenses at 37ºC

Tray inside environmental chamber

Zeiss Immersol W

1.334 (at 23ºC)

Water immersion lens only

Tray inside environmental chamber

Note that Cargille Type 37 is optimal for use at 37 degrees but introduces spherical aberrations when imaging beyond anout 10 microns into aqueous media because it is not refractive indexed matched to water. Zeiss Immersol W in combination with the 60x WI lens might be a better choice in this case, but its RI is corrected for use at room temperature and won't be correct at 37 degrees.

Setting up the Nikon Perfect Focus System (PFS) for multi-point acquisition in Z

The following is a procedure I've worked out for setting up the PFS for multi-point acquisition. I used fluorescent HeLa cells grown on Mat-Tek glass-bottomed 35 mm dishes and mounted in a Solent Scientific insert designed for a range of 35 mm dishes but adjusted to hold this one firmly in place. I cannot say for sure that the procedures will work for all surfaces. Nikon only recommend glass of standard #1.5 coverslip thickness (170 µm).

  1. Make sure that the PFS lever under the microscope stage on the right is in the In position - otherwise the PFS won't work
  2. Focus on the specimen. I focused on the cytoplasm of well spread cells so that my focus plane was relatively near the coverslip
  3. The small green LED on the front of the microscope stand should be lit, indicating that the coverslip is in range of the PFS
  4. If it is not lit then slowly lower the microscope focus until the LED comes on. Note that the LED may only be on in a very narrow range of focuses, so don't focus too fast or you might miss it
  5. Focus up and down until you are about in the middle of the range of focus where the LED is on
  6. Press the Focus button on the front of the microscope to turn on the PFS
  7. Use the Offset adjustment dial to the right of the microscope stand to refocus on the focus plane
  8. Bring up a live image of the plane of focus in the Vox image preview
  9. Use the Offset dial to readjust the focus on the screen, then turn off the Focus button
  10. Start marking points, making sure at each point the small green LED on the front of the microscope is on
  11. If the LED is not on or flickers at any of the points, adjust the microscope focus until the LED is solidly on, then mark the point
  12. After all points are marked, go back to the first point and turn on the PFS to make sure the focus has not drifted. Make any fine adjustments to the offset if necessary
  13. Turn off the PFS and set the Ultraview Focus Drive to Zero
  14. Set the Top and Bottom of the Z series. Note that because zero is at a plane of focus near to the coverslip, the top of the Z series may be further away from zero than the bottom (e.g. Bottom = -5.0 µm, Top = +25 µm)
  15. Review the points to make sure the LED is still on at all of them
  16. Check the Bottom and Top of the Z series settings at a few points to make sure that the focus range is adequate for all of them. Make adjustments if necessary
  17. Go back to the first point
  18. Set up the time-lapse settings, setting the autofocus method to 'Nikon Ti PFS'
  19. You can now either turn the PFS on before starting the time-lapse or leave it off. If you choose the former this should keep the PFS on between time-points, but this might not be necessary if your time-points are close together.

Note that Perkin Elmer don't recommend having the PFS on between time-points, but if there is a lot of focus drift between time-points it may be the only way to stop the focus drifting out of the range of the PFS. Here are some links:

  • Perkin Elmer Tech Note - Nikon Ti PFS - PE's technical note on using the PFS. The last section, 'Multiple planes with secondary drive (piezo), multipoint, over time' deals with the above case. My method differs in that I make sure the PFS is in range initially by adjusting the microscope focus to the middle of the range where the LED is on.
  • Austin Blanco's blog on PFS troubleshooting - Some useful information on the operation of the PFS, ideal specimens and error indicators
  • No labels