Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Troubleshooting

If you link to this troubleshooting page from outside the wiki then please either scroll down or use the following Table of Contents to find the right section

Table of Contents

Leica Confocals

Troubleshooting hardware and software faults on the Leica confocals

If LAS AF has frozen and you can’t quit the software

Table of Contents

Leica Confocals

What to do if the LASAF software says you don't have a valid licence when you try to start the confocal

  1. Quit the software
  2. Unplug the licence dongle from the back of the computer and plug it back in again
  3. Restart the software

LASAF licence dongleImage Added

If you shut the system down - or just restart the computer - that should also work

What to do if the software hangs or if an error won't go away even after you've quit the software and reopened it

If LAS AF is not responding or an error message keeps appearing you must force quit the application and kill its processes

...

If that fails then it will all have to go off and on again, but in practice this is rarely needed if you do the two procedures at the top first.

How to create

...

error reports for the Leica confocals

If the Leica confocals (SPE, SPE2, SPE3 and SP5) crash, hang or suffer any other problems you should create an error report to make troubleshooting the problem easier. LAS AF does not have to be open for you to generate such a report. The image below shows how to create a report from the Windows Start Menu.

...

Check that the transmitted light illumination arm in the vertical position and is not pushed back to allow easy access to the stage. Check that the objective lens turret is correctly in position (i.e. the objective lenses are not halfway between one position and another). The interlock engages when the system is not laser-safe and there is a risk of laser light entering the user's eyes. Putting the above components back into their safe position should clear the interlock condition.

SPE and SPE2: The focus won't go up any further than a certain height so you can't get your specimen in focus

This is most likely caused by somebody either deliberately or accidentally engaging the Focus Stop. If you look at the focus wheel on the right of the stand you will see a narrow Focus Stop wheel between the focus wheel and the body of the microscope. It has two arrows saying Adjust and Set. Rotate the wheel in the Adjust direction and this will disengage the Focus Stop.

If you ever need to use the Focus Stop for any reason please disengage it once you have finished. Also please be careful not to accidentally engage the Focus Stop when you are adjusting the focus knob.

Anchor
SP8scanrot
SP8scanrot
STED: What to do if the scan field rotation controls are not visible

If you are using the STED as a confocal you may from time-to-time notice that the controls for scan field rotation are not visible in the software or on the control panel. This is because the microscope has been used for STED and scan field rotation is disabled so the illumination and depletion lasers remain aligned. To regain control of scan field rotation you need to quit and reopen the software and turn off the STED switch when you see it on the splash screen.

Solent Scientific Chambers

Volocity Time-lapse Microscopes

GFP2: What to do if all the devices are on but when you open Volocity there are no controls for the microscope, filters, shutters or XY stage

This is a software bug where the volocity.exe process does not close when you quit Volocity. This means that if you reopen Volocity the earlier process will still be talking to the microscope and Ludl controller and will deny you access.

Workaround solution:

  1. Quit Volocity
  2. Press CTRL ALT DEL to open the Task Manager
  3. Click on the Processes tab
  4. Re-order the processes alphabetically by clicking Image Name at the top of the column and scroll down to find volocity.exe
  5. There may be several instances of volocity.exe - select and end them all
  6. Close Task Manager and re-open Volocity